橡膠軟接頭漏水的最大的原因應該是因為設備不精確。近一些客戶反響橡膠軟接頭產品在設備和試運行會有漏水現象,出廠前都是經過壓力測驗和緊密關閉性試驗測驗,契合規範後才會出售到客戶手中。上海bob竞技体育減震器有限公司的技能擔擔任職務務的人覺得設備運用有誤,可曲撓橡膠軟接頭在法蘭聯接過程中使用可曲撓橡膠軟接頭本身橡膠端麵的傑出橡膠邊際作為緊密關閉資料來緊密關閉橡膠軟接頭法蘭端麵,所以相同在扣槽橡膠軟接頭容易發生漏水現象,端麵全緊密關閉橡膠軟接頭不會有這種現象,首要原因是扣槽橡膠軟接頭設備時間沒有很好的將橡膠緊密關閉端麵很好的卡進法蘭的凹槽中,這樣橡可曲撓橡膠軟接頭在運用過程中容易發生部分壓力會集在邊際處顯露出來走漏。在可曲撓橡膠軟接頭設備過程中有必要使橡膠邊際卡扣到到法蘭槽裏,所以設備後反法蘭能夠很緊密關閉的卡住橡膠端好,運用中不會呈現滲漏現象。當有部分的設備作業,螺釘不走漏,這是不精確的緊密關閉麵走漏後,擰緊螺釘將損壞橡膠邊際,使緊密關閉麵損害,橡膠球的外表的一小批遭到損壞。這種辦法是不精確的,我廠走漏,該橡膠軟接頭卸下被複原,之後調整設備。
The biggest cause of rubber joint leakage should be due to inaccurate installation.Recently, some customers reported that there would be water leakage in the installation and trial operation of rubber joint products. Before leaving the factory, they all passed the pressure test and tight sealing test, and were sold to customers after meeting the standards.Pine xia shock absorber co., LTD. Shanghai technical bear positions of people think that using the wrong installation, in a flexible rubber joint used in the process of flange connection in a flexible rubber joint of rubber face own outstanding rubber edge to tightly closed as tightly closed material rubber soft joint flange end face, so the same accounting groove soft rubber joints are prone to leakage phenomenon, face all tightly closed soft rubber joints will not have this kind of phenomenon, the main reason is that buckle slot will be a very good rubber joint installation moments don't have rubber tightly closed end face good card into the groove of the flange,This flexible rubber joints in the use of the process is prone to part of the pressure concentrated on the edge of the exposed leak.In the installation process of flexible rubber joint, it is necessary to make the rubber edge buckle into the flange slot, so the anti-flange can be very close to the stuck rubber end after installation, there will be no leakage in use.When there is part of the installation work, the screw does not leak, which is inaccurate tight sealing surface leakage, tighten the screw will crush the rubber edge, so that the tight sealing surface damage, rubber ball surface of a small batch of damage.This method is not accurate, I plant leakage, the rubber soft joint was removed after the reduction of the adjustment device.